Stylish and compact, Retract-A-Gate is a 100% USA-made safety gate that automatically winds up into a small roll when you don't need it. Whenever you need to block an area, you can easily unroll the gate from the reel by using one-hand to pull the handle then guiding the mesh across your stairs, door, or patio and into the opposite pair of brackets. After you lock the gate with the childproof lock, you’re done! It’s that easy. Two low-profile pairs of brackets, which the baby gate hooks into, are attached to both sides of the opening.The reel side of the gate snaps into one pair of brackets.The handle side hooks into the opposite pair of brackets.The lock is a simple push-and-turn mechanism; easy for adults to use, but safe for small children. Retract-A-Gate is 100% USA-Made When looking for a gate to protect your little ones, safety is top priority.When you choose Retract-A-Gate, you get a gate that has been thoroughly tested and proven to do its job. Retract-A-Gate is evaluated yearly at our facility in Dubuque, Iowa and by an independent testing laboratory for compliance with the American Society of Testing and Materials Gates and Enclosures standards, ASTM F1004. Simple Retract-A-Gate Installation Anyone Can Install a Retract-A-Gate! Step 1: Mount the bottom brackets at 3-4” off the floor. Mount the top brackets 30.5” off the floor. If the bottom bracket is on a baseboard, wall spacers (purchased separately) are used behind the upper bracket so both brackets are the same distance from the wall. Step 2: Snap the Retract-A-Gate into the mounted brackets. You’ll hear a small click when it’s secure. Step 3: Easily pull out the retractable mesh using the handle, which causes the mesh to unravel. Step 4: Guide the mesh to the opposite set of brackets, then hook the mesh into the brackets. The total width of the gate assumes that the brackets are pointing inwards. Step 5: Use the childproof lock to secure the mesh. It's that easy! General Use When mounting the gate at the top of your stairs, ensure that the gate is at least 6 inches back from the top of the staircase. If the gate is mounted directly at the top step, a gap can form that a baby or pet could fit through.Retract-A-Gate is usable inside and outside. During extreme temperatures, taking the gate inside will help prolong its lifespan. All exposed metal on the gate will not rust, and the mounting hardware is treated to resist rust. For beach or near-saltwater use, use stainless steel mounting hardware and limit outdoor use by bringing the gate inside.Retract-A-Gates are easily cleanable with only soap and water. Rubbing alcohol can also be applied. Let your gate dry thoroughly before using it again. Baby Use Retract-A-Gate is certified annually by the JPMA to ensure it complies with North American safety gate standards for children 6-24 months. The mesh fabric is a non-toxic reinforced polymer composite. It does NOT contain any material defined as hazardous by the Consumer Products Safety Commission.Retract-A-Gate’s mesh remains flexible so it can rewind into the reel. However, the mesh is taut enough to prevent a child from squeezing under when installed correctly. Here are some tips: Ensure that the gate is locked when in use. Push, then turn the childproof lock to secure the gate. Locking the gate prevents further extension of the mesh.The base of the reel should be in contact with the floor. There should be no more than ¼” gap between the bottom of the mesh and the floor.Add additional tension to the mesh by turning the roll 1/8 of a turn, then locking the gate. Dog Use Retract-A-Gate’s mesh is made from a durable reinforced polymer composite. The mesh was engineered to be scratch resistant and is certified for up to 200 lbs. of push out force. It’s also non-toxic, so there’s no need to worry about exposing your furry friend to harmful chemicals. Retract-A-Gate’s mesh is scratch-resistant; however, it was not designed for use with dogs with behavioral issues. If your dog is prone to excessive biting or chewing, we recommend you purchase a solid steel dog gate. As tough as our mesh is, it can still be bitten through by an aggressive dog. If there is excess slack in the mesh, the distance between your upper and lower brackets may be off. Measure the horizontal distance between each bracket pair. Is this distance identical? If not, adjust accordingly. Cat Use Retract-A-Gate’s mesh is scratch-resistant, non-toxic, and perfect for your feline friend. It was designed to prevent a cat from squirming under the mesh. If your cat is getting under the gate, review the following: Keep the gate is locked when it is in use. The base of the reel should be in contact with the floor. There should be no more than ¼” gap between the bottom of the mesh and the floor.Is there excess slack in the mesh? The distance between your upper and lower brackets may be off. Measure the horizontal distance between each bracket pair. Is this distance identical? If not, adjust accordingly. Retract-A-Gate was designed to be difficult for a cat to climb or jump over. The mesh will tip backwards slightly when a cat climbs up it, causing the cat to lose its balance. At 34” tall, Retract-A-Gate is one of the tallest gates available. However, if your cat loves to jump and regularly clears a three-foot vertical, you will need a taller cat gate. General Use Baby Use Dog Use Cat Use Will Retract-A-Gate cover my opening? How tall is the mesh? Retract-A-Gate assumes that your brackets are pointing inwards. When measuring your opening to see if Retract-A-Gate will work, Retract-A-Gate will cover anything up to a 52 or 72 inch opening. The total distance covered does include the brackets, so for maximum coverage, the brackets need to be pointing inwards.If you’re making up less than 2 inches of space, placing wall spacers under the brackets can help you make up the extra distance. For example, if your opening is 74", placing an inch of spacers under each bracket will allow the gate to cover the full opening, assuming that the brackets are pointing inwards.You can mount the brackets around the corner of an opening. Retract-A-Gate is designed to work at a variety of angles, but mounting the brackets around the corner of an opening does increase the opening distance.The mesh measures 34" vertically. The reel (on the right side in the above picture) is 38" tall, and it can be placed on either the right or left side of the opening. Retract-A-Gate Accessories New Wall Spacer Set (not included) Wall Spacers are used to make your installation vertically plumb. When installing the bottom bracket on your baseboard, place a number of wall spacers equal to the thickness of the baseboard under the upper bracket.Each set includes 10 wall spacers. Each spacer is 1/8 inch thick. Purchasable on our direct Web Shop. New Universal Mounting Bracket Kit (included) Each Retract-A-Gate comes with a Universal Mounting Bracket Kit. Each kit contains the following items: 4 hardware-mounted Universal Mounting Brackets8 2-inch long screwsInstallation guide (not pictured) Purchasing additional brackets allows you to easily move your Retract-A-Gate between two locations. Additional Universal Mounting Bracket Kits are available for purchase on our direct Web Shop.
